Multifunctional Display Module MOD 21

Multifunctional Display Module MOD 21

Display module for simultaneous operation of two encoders, absolute or incremental in any combination 8 control inputs and 16 control outputs, 40 cam switches

SSI-Interfaces

For operation of absolute single- or multiturn- encoders with resolution up to 30 bit with serial SSI-Interface.

Incremental-Inputs

For operation of incremental encoders with 3 or 6 output channels, RS422 line driver or push-pull outputs. Optically insulated with optocoupler.

Display-Scaling

Scale factor, adjustment values and counting direction are separatly programmable for both encoders.

Programmable Control-Inputs

8 optically insulated control-inputs are programmable for various functions, e.g. storing of display data or enable of counter.

Programmable Control-Outputs

16 optically insulated control-outputs, which can be programmed separately by 40 cam switches as a comparator, cam switch or pulse switch. The cycle time is only 500 µs.

Analogue-Output

1 optically insulated programmable analogue-output, which can be used as voltage or current output. High precision D/A-converter with 16 bit resolution. For data source of the analogue output position or velocity of one encoder can be selected.

Serial Interfaces

RS232C One display module can be connected to a PC for programming and reading data.
RS422/485 Up to 31 display modules can be connected to a PC.
CANBUS Up to 32 display modules can be connected with CANBUS.

 

Type explanation

MOD 21
MOD 21- 1 2
Analogue output X
Serial interface X X
Programmable control inputs X X
Programmable control outputs X X
Display scaling X X
Incremental input X X
SSI interface X X

Technical data

Technical Data
Supply voltage +10 ... 35 VDC
Power consumtion < 150 mA (ohne Last / without load)
Cycle time 500 µs
Display range -9999999 ... 99999999
Display rote 7-Segment-LED-Anzeige 8-stellig mit 14 mm Ziffernhöhe
8-digit 7-segment red LED display, 14 mm high
Data memory EEPROM
Operating temperature 0 ... +50°C
Connections Klemmleiste / Terminal block
max. 1,5 mm2
Sub-D-Stecker /Sub-D connector
Weight < 0,7 kg
Protection class Frontplatte / front: IP 50
mit Schutzgehäuse / with protective cover: IP 54
Rückseite / rear: IP 20
Incremental input
Circuit Optokoppler
Input level 5 VDC High +2,8 ... +5 VDC
Low 0 ... +0,8 VDC
Input level 24 VDC High +10 ... 35 VDC
Low 0 ... +5 VDC
Input restistance 3 kOhm, Uin = 24 V
350 Ohm, Uin = 5 V
Input frequency max. 150 kHz
Pulse width signal M min. 2 µs
SSI interface
Clock frequency 125 kHz, 139 kHz
Clock output RS422
Clock input Optokoppler RS485
Control inputs
Circuit Optokoppler
Input level Low 0 ... +5 VDC
Input level High +10 ... 35 VDC
Input restistance 1,8 kOhm, Uin = 24 V
Control outputs
Circuit Optokoppler mit NFET-Treiber
Supply voltage max. +35 VDC
Output voltage min. Vcc -2 V, Iout = 50 mA
Output current max. 500 mA, kurzschlussfest / short-circuit proof
Analogue Voltage-Output
oltage range -10 ... +10 VDC
Resolution 305 µV = 16 Bit
Temperature stability max. 20 ppm / °C
Output current max. 12 mA, kurzschlussfest / short-circuit proof
Analogue Current-Output
Current range -20 ... +20 mA
Resolution 610 nA = 16 Bit
Temperature stability max. 20 ppm / °C
Burden max. 550 Ohm
Serial interfaces
RS232C Baudrate 9600 .. 57600 Bit/s
RS422/485 Baudrate 9600 .. 57600 Bit/s
CANBUS
Protocol AP-Link
PDOs 1 Eingang, 1 Ausgang, 64 Bit breit
1 Input, 1 Output, 64 Bit length
Baud rate 20 kBit/s .. 1 MBit/s

Outline drawing

Multifunctional Display Module MOD 21

Version ZE 618-711 · Subject to change

Go back

INDUcoder® · INDUcoder Messtechnik GmbH, Kaiserstraße 316, 47178 Duisburg, Deutschland
Tel: (0203) 57047-0, Fax: (0203) 57047-20, E-Mail: info@inducoder.de, Internet: www.inducoder.de